How To Remove Faux Brick From Wall

iStock

Information technology's hard non to love the wait of exposed brick, just not anybody is lucky plenty to have it in their home. Don't worry; you can mimic the look with these tips.

Whether it'southward a modernistic home, a country cottage, or an industrial-fashion loft apartment, exposed brick is an incredibly sought-afterward expect. Unfortunately, not anybody has it readily bachelor, hiding backside their drywall and begging for the not-and so-gentle touch of a sledgehammer. Merely, if you're up for learning how to build a fake exposed brick wall, information technology volition be fairly piece of cake to reach.

There are two chief methods for doing so. I involves using a brick veneer or "thin brick" (essentially brick tile) and the other involves using a hardboard or cream panel designed to mimic real exposed brick. This guide will encompass both.

How to Apply Brick Veneer to a Wall

iStock

Step one: Fix the wall

You'll be calculation quite a scrap of weight to the wall, so be certain that the drywall is in proficient condition. Repair any holes or dents with articulation compound, a putty knife, and a sanding block first. As well, remove whatsoever electrical outlet covers and switch plates from the wall. Don't forget to remove nails used for movie hanging, too.

Step ii: Create a direct (or level) line on the wall

Your first form needs to be every bit straight as possible, as all subsequent courses volition build off it. If your floors and walls are level, y'all can employ a light amplification by stimulated emission of radiation level or spirit level to depict a level line across the wall. If your floors are out of level, it's often better to measure and snap a chalk line against the wall instead.

Stride 3: Apply the first class

Using the caulk gun with structure adhesive, squeeze a zig-zag pattern of adhesive on the back of each brick earlier applying them along the reference line. Check to ensure they're straight (not necessarily level).

Utilise the grinder fitted with a masonry wheel to cutting any bricks to shape or length for corners, outlets, and other areas a full brick won't fit. Be sure to wearable safety glasses while cutting.

Footstep 4: Utilise the post-obit courses

Once the outset course is laid, utilise the same technique for the following courses. Stagger the joints then the center of each new brick is direct over a joint below it. Be sure to utilize a tile spacer between each brick to grade consistent, even joints. Wait for the wall to dry out.

Pace v; Apply mortar mix betwixt the joints

Utilise the bucket, paddle mixer, and drill to combine the mortar mix and water according to the directions on the handbag. Scoop mortar mix into the mortar bag with the trowel. Using even pressure, place the tip between the bricks and clasp the mortar mix into the joint. Use the jointing tool to smooth joints for an exposed-brick wall look.

Faux Brick Wall with Brick Veneer: Tools and Materials

How To Install Brick Paneling

iStock

Step 1: Prepare the walls

Before installing the faux brick paneling, remove all light fixtures, outlet covers, and wall plates from the wall. If there are any dents or holes, repair the brick with articulation compound, a putty pocketknife, and a sanding cake.

Run a strip of painter's record forth the floor and ceiling side by side to the wall. Utilize the stud finder to locate all the wall studs and brand corresponding marks on both strips of tape.

Footstep ii: Create a straight line

Faux brick panels either come up in modest sections or large four×8 sheets. Regardless of the panels you chose, they need to be straight and consistent to look good. For smaller panels, use a laser level or spirit level to create a horizontal line to indicate the starting tiptop of the first form of panels. For larger panels, use a level to create a plumb line 48 inches from the adjacent wall.

If your walls, floor, or ceiling are significantly out of level, it might look better to follow the slope. You can still create a direct line by measuring and snapping a chalk line across the wall.

Step 3: Cut and exam-fit the panel

Measure the location of the first panel and cut it to size with a round saw. If there are any outlets or electrical boxes, have careful measurements and transfer them to the panel before cutting them out with a jigsaw or multi-tool. Test-fit the panel to ensure information technology fits as it should.

Pace 4: Apply adhesive to the back of the console

While most imitation brick paneling is calorie-free, construction agglutinative or panel adhesive helps proceed information technology secure. Employ the caulk gun to squeeze a bead upwards and down the back of the panel. Be careful non to become within 1½ inch of the edge, or information technology will seep out when installed.

Footstep 5: Install the console

Carefully align the panel with the reference line and any outlets or switches before pressing information technology against the wall. One time in place, bulldoze staples through the panel and into the studs. If possible, staple into the simulated grout lines as the staples will blend in ameliorate with grout than with the cherry faux bricks.

Step 6: Continue down the wall

Align the adjacent panel with the edge of the previous panel or level marking. It'due south critical that the seams between the panels be equally tight every bit possible and that the bricks appear aligned, then take intendance to get this correct. Measure for whatsoever outlets or switches and transfer the measurements to the new panel for cutting before installing it on the wall and moving to the next console.

If yous're careful when aligning the seams and stapling, no one will be able to tell that the exposed brick paneling isn't the real deal. And so hang a few pictures, get the room in order, and kick back while enjoying your new false exposed brick wall.

False Exposed Brick Wall Paneling: Tools and Materials

www.thisoldhouse.com

Source: https://homestyling.guru/home-makeover/how-build-a-diy-faux-brick-wall/

Share this post